Shop headings: New Spares | Used Spares | Accessories | Brands
Carb gasket kit / rebuild kit for 1 Dellorto PHF carb. Suitable for all PHF carbs with accelerator pumps including PHF36. Dellorto ref. 52514-77
Carb overhaul kit, float bowl seal FUA90001 and fuel filter FUA60888 also available separately to this carb seal kit
5 in stock
14939950 GU14939950 14 93 99 50
1493 9950 1493.9950 14.93.99.50
Also fits Hesketh, Laverda
£18.75
INC VAT
£15.62 EX VAT
Ball bearing for brakelight switch
5 in stock
92295708 GU92295708 92 29 57 08
9229 5708 9229.5708 92.29.57.08
£0.90
INC VAT
£0.75 EX VAT
UFI 30 886 00 flat type air filter, paper filament in rubber surround
NB Packaging may vary. See SIA28367 for the equivalent reusable K & N filter
5 in stock
28113660 GU28113660 28 11 36 60
2811 3660 2811.3660 28.11.36.60
£8.00
INC VAT
£6.67 EX VAT
M12 A2 fine thread stainless steel lower crashbar mount bolt for models requiring longer crash bar bolts
5 in stock
£6.00
INC VAT
£5.00 EX VAT
Fork seal
Supercedes Guzzi ref. 90403853, not for models with Marzocchi forks (e.g. V35 TT)
5 in stock
90403857 GU90403857 90 40 38 57
9040 3857 9040.3857 90.40.38.57
£7.20
INC VAT
£6.00 EX VAT
40mm fork seal. Two fork types are used on recent small twins, we recommend checking your old fork seal before opening
Also known as Guzzi ref. 90404052, 904040953, 90404051, 90404054
5 in stock
90403952-z 90403952 GU90403952 90 40 39 52
9040 3952 9040.3952 90.40.39.52
£8.00
INC VAT
£6.67 EX VAT
Bearing used as UJ carrier bearing on pre 2007 models (see TRA90062 for retaining circlip). Used as outer crownwheel carrier bearing on CARC units
5 in stock
92204230 GU92204230 92 20 42 30
9220 4230 9220.4230 92.20.42.30
£14.40
INC VAT
£12.00 EX VAT
£2.08
INC VAT
£1.73 EX VAT
Threaded straight throttle cable adjuster for carb top with M6 thread
5 in stock
12937200 GU12937200 12 93 72 00
1293 7200 1293.7200 12.93.72.00
£4.20
INC VAT
£3.50 EX VAT
Dimensions:
10mm threaded shank, 11mm across flats, 8mm OD at base, 15mm from tip to underside of flats
Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models
Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.
5 in stock
£8.20
INC VAT
£6.83 EX VAT